![\"\"](\"https:\/\/energio.fi\/wp-content\/uploads\/2025\/09\/WhatsApp_Image_2022-07-17_at_16.52.30_1024x1024.jpg\")
<\/p>\n<\/p>\n
I’m eating lunch at home when my friend Patrick calls and excitedly explains how well the solar power system he installed last summer produced despite the snowfall yesterday (February 19, 2023). We agreed that we should turn this into a direct customer interview. <\/p>\n
So last summer, we worked together to install ground-mounted solar panels for Patrick. Patrick took care of the rack, foundations, and installation of the panels himself, while we delivered the panels and did the electrical work. <\/p>\n
System<\/p>\n
The yield has surprised me positively. During the summer it produced as I expected, but for example September-October was really good. In September the system produced a total of 428.44 kWh, while the electricity purchased from the grid was 383.04 kWh. The best production day was almost 30 kWh in September. <\/p>\n
I had calculated that the system would produce from April to September, but the winter yield has surprised me. This year (January-February 20th) the yield has already reached almost 100 kWh. <\/p>\n
February has been incredibly good overall. The panels have been easily cleaned, so even on a snowy day they have been able to produce about 400 W of power, which is about the same amount as the air source heat pump used to heat the house consumes in sub-zero temperatures. Incredibly good, I wouldn’t say. <\/p>\n
The two-sidedness of the panels seems to work well, at least in winter. For example, yesterday (February 19, 2023)<\/span> before the snow was cleared, the back side alone produced about 50W of power. That is 10-15% of the entire system’s output yesterday. On sunny winter days, the reflections seemed to produce up to 25% of the power. Of course, this was difficult to prove with home tools. <\/p>\n The yield on February 19th was incredibly good even though the weather was snowy all day. The cleaning of the panels is clearly visible in the yield curve after 12:00 and 15:00. Before this, the yield is caused by reflections from the back of the panels, as the panels were under about 10 centimeters of snow before the cleaning. <\/em><\/p>\n Making the racks was quite a task. First I had to think about how many panels I wanted, then I had to figure out the installation spacing, the dimensions of the panels, how the rails and fasteners would fit, think about material choices, how to make the foundations, what kind of groundwork should be done. In the design, I had to take into very careful consideration how to make the rack straight and sturdy and one that would last over time. I also had to think about how to meet the warranty conditions for the panels. <\/p>\n Hauling the goods to the site was a reasonable task, even if a trailer was available.<\/p>\n I got a ground drill from a rental shop and drilled as deep as I could. It was a pretty rough job, even though it was the smallest ground drill they had. I think the device was a bit of a pain in the ass. <\/p>\n Then a spike was driven into the hole in two of the posts, a second four-pointed post was driven into the ground, and then a large jack was used to ram the posts into the ground. Finally, the concrete was poured. A total of 18 posts were driven into the ground. Each one should be straight and the rows straight. Then the tops were plumb-wired when the concrete had dried and at right angles with a hand circle. At right angles with angle irons and large bolts to assemble the entire rack. <\/p>\n I still had to make suitable mounting points for the rails. I also installed the panels myself. <\/p>\n It took about three weeks of evening work to make the scaffolding.<\/p>\n <\/strong>I wouldn’t do it myself again! It was a project that took so much time, effort, and money. <\/p>\n At the time of purchasing the system, there were no sensible solutions on the market. With your help, I looked into scaffolding, but no sensible solutions were found. These were either too small or far too big, and making the foundations was also a big problem in many cases. Either a large concrete slab would have had to be made or an excavator would have been needed to ram the piles. Scaffolding with two rows of panels on top of each other would have blocked the view from the house. <\/p>\n One rack was found where the foundations were ready-made in the form of rebar spikes that were hammered crosswise, but the rack itself was a real mess and the freight would have cost the same as the entire rack itself. In addition, the rack was only suitable for one panel model that was not double-sided. <\/p>\n So, in short, if I had found a ground rack with, for example, screw pile foundations, I would definitely have chosen one. <\/p>\n Oh wow! I have to tip a couple of friends who have asked about my power plant. <\/p>\n Read more \/ground installation<\/p>\n What do you think are the pros and cons of ground mounts compared to roof-mounted systems?<\/p>\n Pros<\/strong><\/p>\n![\"\"](\"https:\/\/energio.fi\/wp-content\/uploads\/2025\/09\/Refe_600x600.png\")
<\/p>\nYou made the rack yourself, what kind of project was this?<\/strong><\/h2>\n
If there had been a working ground rack on the market, would you remake the racks yourself or purchase the racks?<\/strong><\/h2>\n
By the way, we have just released such a ground rack<\/strong><\/h2>\n
Ground rack pros and cons<\/h2>\n